Home > Error Code > Panasonic Ac Error Codes

Panasonic Ac Error Codes

Contents

Check indoor unit control PCB. Thanks again, Dave Bowles Hi Dave it is impossible to see weather it is short of gas until someone puts a set of gauges on to see how the system is Resolving such issues involve removing dirt from the contacts and reconnecting the sensor. Stops immediately when restarted. • Layer short in the compressor 2. weblink

For any job offer please check my profile! 05-09-2009,07:00 AM #7 DaveBowles View Profile View Forum Posts View Blog Entries View Articles Registered User Hey, I am new to : RE Slim P Series K air conditioner fault codesMitsubishi PWFY air conditioner fault codesPanasonic air conditioning fault codesToshiba air conditioning fault codesService & MaintenanceCauses of Air Conditioner FailureMobile Air Conditioner safetyPortable air For any job offer please check my profile! 06-09-2009,11:06 AM #11 DaveBowles View Profile View Forum Posts View Blog Entries View Articles Registered User Hey, I am new to : RE Check outdoor unit control PCB.

Panasonic Inverter Aircon Error Code

Correcting all the causes will solve the issue. F95 (overheating outdoor coil) – such issues are a result of blockages, cool mode, dirty condenser coil or low gas. H12 (ID/OD compatibility problem) – this is usually caused by over-indexed or under-indexed multi system. Check indoor unit EEPROM.

Compressor trouble (locked, etc.) • Replace the compressor. 2. The system returned: (22) Invalid argument The remote host or network may be down. H98 (indoor coil overheating) – overheating problems can be caused by high indoor temperature, faulty filters and indoor coils. Panasonic Air Conditioner Error Code H11 P194-way valve locked • Judgment occurs after compressor has been ON for 5 minutes.Indoor heat exchanger temp, drops although compressors are ON in heating mode: [min(E1.

However, the aircon codes may fail to function from time to time and this can be quite distressing. Panasonic Split System Timer Light Flashing Check inverter control PCB. • Wiring trouble Compressor motor output trouble. Emergency operation = O Primary location to verify = • Outdoor temperature sensor (detective or disconnected) Diagnosis display = H28 Abnormality / Protection control = Outdoor heat exchanger temperature sensor abnormality Home Contact Panasonic Split Air Conditioner Error Codes April 19, 2015 Panasonic A blinking lamp for other than the signal receiving unit filter shows that a problem has occurred in the

F98 (over current protection) – can be caused by excess charge or problems with outdoor heat exchanger. Panasonic A/c Fault Codes H14 (faulty indoor air sensor) – can be a result of dirty contact surfaces, disconnected or faulty sensors. E13Error in Indoor Unit Transmitting Signal to Remote Controller E14Main Unit duplication in Simultaneous-operation Multi Control (detected outdoor unit) E15Automatic Address Alarm (capacity too low) E16Automatic Address Alarm (capacity too high) Resolving the problem requires general cleaning maintenance and increasing gas levels.

Panasonic Split System Timer Light Flashing

Refrigeration-Engineer.com, the administrators and Moderators of this site are not responsible for content posted here. How To Solve Common Panasonic Aircon Codes? http://alltroubleshooting.net/air-conditioner/panasonic-air-conditioner-error-codes/ Generated Mon, 24 Oct 2016 00:43:39 GMT by s_wx1011 (squid/3.5.20) Panasonic Inverter Aircon Error Code Results 1 to 12 of 12 Thread: Panasonic Fault Codes Thread Tools Show Printable Version Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode Switch to Threaded Mode 04-09-2009,11:26 Panasonic Air Conditioner Error Codes Download The indoor unit power was cut off after automatic address setting was completed.

INV Compressor Actuation Failure (including locked) due to DCCT Failure Panasonic S-36PU1E5A air conditioner error codes Remote controller displayCause Nothing is displayed.The remote controller is not connected correctly (power trouble). have a peek at these guys Check intake temp, sensor (TS). 2. H30/31 (faulty outdoor discharge sensors) – wipe off any dirt from the contact surface and reconnect the sensor. Indoor heat exchanger temp, rises although compressors are ON in cooling mode: E2 i 104 'F. Panasonic Air Conditioner Troubleshooting

P15Insufficient gas level detected.The following conditions continue for 1 minute. • Discharge temp, is 203 *F or higher. • Electronic control valve is at step 480. • Current value from MDC Multi)Indoor unit judges that type does not match outdoor unit type.Recovery at power reset1. One of them is represented by the error codes` system. http://sisei.net/error-code/panasonic-error-codes-dvd.html The remote controller of an indoor unit where the indoor unit address is not set is inadvertently operated. (Communications with the outdoor unit are not possible.) E02The remote controller is not

Wipe off any dirt from the contacts and reconnect sensor to solve the issue. Panasonic Air Conditioning Fault Codes Pdf F97 (high compressor temperature and discharge) – this issue occurs due to faulty compressors or low gas charge. Check outdoor unit control PCB.

Have you a record of the gas that may of been added to the system, because if the pipework is over 5 meters then gas should of been weighed in.

Loose screws between HIC control PCB and radiating plate 3. Alarm is output when inverter stops (pre-tnp) consecutively 4 times.Recovery at restart1. For information on how to connect to the signal receiving unit, refer to the instruction manual that came with the dedicated service check lines. Panasonic Tv Fault Codes Check to ensure there is fluid air flow.

Compressor does not run. (Overcurrent protection circuit activates after a certain period of time following compressor start.)Inverter stops after alarm is detected.Recovery at restart1. The larger unit has about 5m of pipework, the smaller lass than 2m. Electronic control valve trouble 3. this content Check inter-unit control wiring. 2.

H01Over currentInverter stops after alarm is detected.Recovery at restart1. I find them very professional in their work. F08Disconnection, open circuit, or short circuit in outdoor air temp, sensor (TO)Open circuit or short circuitAutomatic recovery1. Any help much appreciated, thanks, Dave Bowles 04-09-2009,02:38 PM #2 nike123 View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Moderator Site Moderator : and general nice

H27 (faulty outdoor air sensor) – this is another common problem caused by faulty or dirty contact surfaces as well as disconnected sensors. What's New? Recovery at restartCheck refrigerant cycle (gas leak). Routine maintenance can resolve issues of operated float switches and H21 functions.

Outside units are CU-E9CKP5 and CU-E15CKP5. This forum is a free and open discussion board.