Home > Hp Laserjet > P3005 Error

P3005 Error

Contents

over time solder connecting chip leads and printed board crack causing disconnection. I was about to throw them out when I came across this thread. The problem is cold solder joints and nothing else. Verify that the media size matches the tray settings and the dial on the tray. http://sisei.net/hp-laserjet/p3005-error-49.html

It will even have the model number since the same board is used for duplex and non duplex models but model ID'd when the new board is installed. by frieste on May 2, 2008 at 9:15am Add comment Please sign in to comment Does nobody have any information on how to take this thing apart? Pressing any button during the 10-second auto-continuable error message overrides the auto-continue feature, and the button function takes precedence. Using a small solder gun or hair drier or preferably hot air equipment, apply even heat on the leads as you press down the chip.

Hp P3005 Memory Error Replace Dimm

Then, without the blow dryer I booted it again & still got the dead display -- no light at all. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew No action necessary. by greenfishfiles on May 21, 2009 at 1:45pm Add comment Please sign in to comment 0 Fuser Sleeves are gray, black, or brown.The LaserJet 2200 sleeve they sell on this site

Turn on the device. Press (SELECT) to continue printing. To remove this message from the display, press (SELECT). P3005 Formatter Board The device is attempting to eject these pages automatically.

Press (SELECT) to continue printing. No action necessary. Privacy Policy Terms of Use Sign Up Login Add Question greenfishfiles asked May 19, 2009 at 8:23pm 0 HP DeskJet 400 HP LaserJet P3005 41.2 error Not really a question...well, maybe Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order Minimum Returns Shipping Freight

If the message persists, contact HP Support. 49.XXXXX ERROR alternates with To continue turn off then on A critical firmware error has occurred. Hp Laserjet P3005 Memory Remove any media from the duplexer. Press (DOWN) to see step-by-step information. Reinstall the print cartridge, and then close the top cover.

Hp Laserjet P3005 Hangs During Startup

Turn the device off and then on. 2. http://www.fixyourownprinter.com/forums/laser/55786 PAPER PATH JAM FRONT DOOR alternates with For help press (HELP) A page is jammed in the paper path. Hp P3005 Memory Error Replace Dimm Use HP Web Jetadmin software to delete files from the RAM disk memory and try again. Hp P3005 Cold Reset I'm going to try the DC controller for the fun of it..

My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance? check over here If the device is on a network, check that you are printing to the correct device. Incorrect The PIN number is incorrect. Printing can continue, but unexpected behavior could result. Hp Laserjet P3005 Troubleshooting

If a critical error persists, service is required. Try a different driver. A message other than READY appears on the control-panel display. his comment is here To exit, press (HELP). 13.XX.YY JAM INSIDE REAR DOOR alternates with For help press (HELP) A jam has occurred in the rear door area.

They change as the state of the device changes. Hp Laserjet P3005 Replace Dimm 1 The 2420 I had lasted about 5 years and worked great - would still have it if the fuser drum (I think that's what was the problem) hadn't become scratched and There a song about this, M I C K E Y M O U S E.

Press (DOWN) to see step-by-step information.

If the message persists, contact HP Support. 51.XY ERROR alternates with To continue turn off then on A device error has occurred. Remove the duplexer from the rear of the device. If the error occurs when the device is first turned on, turn off the device, disconnect the LAN cable, and then turn on the device. Hp Laserjet P3005 Printing Blank Pages Release the four tabs in the center of the black paper guide inside the lower rear door.

BUT, when it goes to sleep mode it will not come out of sleep so I have to re-boot it then. If the message persists, contact HP Support. 22-USB I/O BUFFER OVERFLOW alternates with To continue press (SELECT) The device's USB buffer has overflowed during a busy state. Initializing This message appears when the device is turned on and begins initialization. weblink Then, release (SELECT) Press (DOWN) to scroll through the available languages.

by unknown on Jul 23, 2008 at 8:12am Add comment Please sign in to comment 0 Do you know how to open the duplex tray? Checking paper path The engine is turning the rollers to check for possible jams. If the board you receive does not do this, then it has been used before. MEM TEST FAILURE REPLACE DIMM 1 The memory DIMM has failed.

It should not have melted it.170 Celsius = 338 Degree Fahrenheit. Check the Jetdirect configuration page to verify that the network protocol status and settings are correct for the device. If this firmware image is newer than the one installed on the device and the device can receive a firmware update, download the newer firmware upgrade. 5. Generated Sat, 22 Oct 2016 09:09:49 GMT by s_ac5 (squid/3.5.20)

by frieste on May 7, 2008 at 1:40pm Add comment Please sign in to comment -1 Again, I appreciate your concern, but I am not an idiot. Receiving upgrade A firmware upgrade is in progress.