Restart, this will be self-correcting. 4. No luck please reset the treadmill, follow this steps and fix it. Are you sure there is one on that board?I also checked all connections and they appear OK. In very rare cases, a defective upper circuit board can cause this error and the circuit board will need to be replaced. navigate here
Replace the fuse and retest. External electrical noise (AC line noise) can interfere with the (RPM) signal between the power supply and the control panel. Insert magnetic key, version will display in Data window. 2. Insert the magnetic key back into the control panel and do not touch any keys, if the error occurs, replace the keyboard membrane. 2.
Pacemaster Treadmill Error Code 31
Also, check the two wires on the optical sensor for any sign of damage, if the wires are damaged, replace the optical sensor. 5. During operation someone fell on to the 10/8/2016 10/8/2016 J.T. Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. If the error still occurs - 4.
Replace the control panel circuit board, the reed switch is not functioning. Check the strobe disc holes for dust accumulation, if there is a build up of dust, clean out the holes. The material appearing on LIVESTRONG.COM is for educational use only. Pacemaster Pro Plus Parts John H 62.911 προβολές 5:32 Sole F80 LS1 Error - Διάρκεια: 3:17.
In some cases, the wire harness can cause the error code. 2. Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. It looks like a fat ... Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices.
This may happen because the elevation motor is not running, the elevation potentiometer has failed or the elevation motor internal gears that drive the elevation potentiometer have stripped. Pacemaster Pro Plus Treadmill Dead Sensor Things You'll Need Hex wrench Magnetic key Related Searches THE LIVESTRONG.COM MyPlate Nutrition, Workouts & Tips GOAL Gain 2 pounds per week Gain 1.5 pounds per week Gain 1 pound per Credentials confirmed by a Fortune 500 verification firm. If this does not correct the error, follow steps 1 through 3 as described above.
Pacemaster Pro Plus Treadmill Troubleshooting
Press and hold simultaneously Calories and Aerobic Points buttons (for the ProClub use the Level+ & Level- Buttons) until unit beeps. http://www.justanswer.com/fitness-equipment/5cbr8-pacemaster-proelite-giving-error-code-22.html User is pushing the tread belt when the magnetic key is inserted into control panel. Pacemaster Treadmill Error Code 31 Treadmill remains on when Magnetic Key is Removed - This occurs when the reed switch (a component on the upper circuit board) fails. Pacemaster Pro Plus 2 Error Code 31 Power up the treadmill and touch the incline up button.
If this does not correct the error, follow steps 3 through 7 as described below. 3. check over here After 2 seconds Set Weight LED will begin to blink. 3. atkmic 1.092 προβολές 2:12 NordicTrack Treadmill Troubleshooting For Noise - Διάρκεια: 5:32. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Pacemaster Proselect Treadmill Manual
Replace if needed. 3. Fit 2 Run 14.701 προβολές 1:01 PaceMaster Treadmills - Διάρκεια: 4:42. Check the elevation motor and wiring for continuity and shorts to ground. his comment is here If the error is corrected, install the spare wire harness.
Replace the control panel circuit board. Pacemaster Treadmill Error Code 24 Add a Picture/Graphic Caption (optional) Click here to upload more images (optional) Add a Picture/Graphic Caption (optional) Add a Picture/Graphic Caption (optional) Add a Picture/Graphic Caption (optional) Step 5 Unplug the treadmill and check that the drive motor connection and ceramic fuse are securely attached and do not show signs of wear if you receive error code 425.
Please try the request again.
Then select it. Simply click here to return to Pacemaster. Very rare: A power brownout during operation. Pacemaster Pro Plus Treadmill Owners Manual Ad Choices Login|Contact Us Exercise Equipment Exercise Equipment Repair Questions?
Credentials confirmed by a Fortune 500 verification firm. This is usually caused by a stuck elevation relay on the power supply board or a damaged or shorted wire harness. If the error still occurs -- 6. weblink So the error code is being caused by something else.
If there is no movement from the elevation mechanism, check the fuse on the power supply circuit board (See Power Supply Replacement). If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. Replace the elevation motor. Use the STOP key or let the time countdown to 0. 2.
VAnsteenhuyseDear sir, I have a Trimline T 325 (motor 180 V 10 A) Can I buy spare parts for this type ? PANEL 00 - 18 - (PAn EL 00 - 18) Indicates the keyboard membrane has a stuck key. On top of the motor there is a sensor where the disc passes through. Turn the left and right tread belt screws located on the back of the treadmill a half-turn clockwise.
In most cases, replacing the optical sensor assembly will correct the problem. 2. Slowly turn the pot counter clock wise until the motor runs smoothly - the speed window should now read between 1.8 and 2.0. Bypass the wire harness between the control panel circuit board and the power supply circuit board. I'm assuming the model is the Pro Select.
DISC GAP ERROR - (diSc gAp Err) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. Press and hold simultaneously the + and - buttons in the Time Window for 3 seconds then release. What is the motor size on the horizon treadmill 5.1 9/23/2016 9/23/2016 Louie LifeSpan TR1200i Folding Treadmill The treadmill makes a 9/22/2016 9/22/2016 J.T. Error Code 53 - Elevation Error 34 Second time out.
If the error still occurs - 5. Replace the power supply circuit board. If, upon startup, the elevation readout is at 15% and the treadmill is level, remove the motor cover (See Motor Cover Housing) and disconnect the wire harness and the elevation potentiometer If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet.