Home > Pacemaster Pro > Pacemaster Pro Elite Error

Pacemaster Pro Elite Error

Contents

Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. treadmilltech is online now I have a PaceMaster ProElite treadmill that has an error code Resolved Question: I have a PaceMaster ProElite treadmill that has an error code #31. If there is no click noise from the power supply, the elevation relay(s) are not functioning. Replace the power supply circuit board. navigate here

Re-insert the magnetic key to resume normal operation. I have the Pro-Form Hybrid Trainer - the elliptical and 9/18/2016 9/18/2016 J.T. Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices. Restart the treadmill, if the error still occurs - 2.

Pacemaster Treadmill Error Codes

Check the elevation fuse on the power supply. If there is no voltage seen, the wire harness or the upper control panel circuit board is defective and will Need to be replaced. In some cases, the wire harness can cause the error code. 2.

What is the motor size on the horizon treadmill 5.1 9/23/2016 9/23/2016 Louie LifeSpan TR1200i Folding Treadmill The treadmill makes a 9/22/2016 9/22/2016 J.T. If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. If you are getting the proper voltage then replace the lower control board(motor controller). Pacemaster Proselect Treadmill Manual treadmilltech is online now My Pacemaster ProElite is giving me an error code 22.

If the elevation does not raise up and the elevation fuse did not blow, touch the incline up button and listen for a click noise from the power supply. Pacemaster Pro Plus 2 Error Code 31 Generated Sun, 23 Oct 2016 21:27:52 GMT by s_wx1085 (squid/3.5.20) Restart, this will be self-correcting. 4.

IF THERE IS NO MOTOR MOVEMENT, check the wiring between the power supply circuit board and the drive motor for good connection shorts to ground and continuity. 2.

The speedometer isn't 10/2/2016 10/2/2016 J.T. Pacemaster Pro Plus Treadmill Dead Sensor Err Code 24 - (Hi Acceleration Error) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. This is the button test mode. Err Code 31 - (Dead Sensor) Indicates that the control panel is not sensing movement of the drive motor.

Pacemaster Pro Plus 2 Error Code 31

After 2 seconds Set Weight LED will begin to blink. 3. No Share this conversation Related Exercise Equipment Questions Question Date Submitted My sears proform xp 680 cross trainer thread mill won't stay 10/20/2016 10/20/2016 J.T. Pacemaster Treadmill Error Codes The following section explains each one of these error codes and the steps that should be taken to correct the problem. Pacemaster Pro Plus Treadmill Troubleshooting If the error is corrected, install the spare harness.

Horizon ct 5.0 I have hit 150 miles and need to lube to 9/19/2016 9/19/2016 J.T. check over here It should not be used as a substitute for professional medical advice, diagnosis or treatment. If there is no movement from the elevation mechanism, check the fuse on the power supply circuit board (See Power Supply Replacement). OK - I was able to hook up a battery and the motor worked - so it does not appear to be the motor. Pacemaster Pro Plus Parts

Do not use a power strip. I wanted to disassemble my cardio zone fast tract to move it 9/4/2016 9/9/2016 J.T. Do not use a power strip. his comment is here What Customer Question My Pacemaster ProElite is giving me an error code 22.

This indication will appear between five to eight seconds after the start button is pressed. 1. Pacemaster Pro Plus Treadmill Owners Manual If this does not correct the error, follow steps 1 through 3 as described above. Replace the power supply circuit board.

If the error is corrected, install the spare wire harness.

If the error still occurs replace the control panel circuit board. If the error still occurs - 4. Tomahawk DIY 12.695 προβολές 16:25 Pace master treadmill - Διάρκεια: 2:00. Pacemaster Pro Plus Rpm Sensor Step 3 Stop pushing the belt if error code 117 appears on the control panel.

Replace the drive motor. Fit 2 Run 14.701 προβολές 1:01 Pacemaster Treadmill , Calgary Canada - Διάρκεια: 1:40. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. http://sisei.net/pacemaster-pro/pacemaster-pro-elite-error-code-22.html Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release.