Home > Pacemaster Pro > Pacemaster Pro Plus 2 Error Codes

Pacemaster Pro Plus 2 Error Codes

Contents

Tobias Hock 1.389 weergaven 2:00 How To Reset the Treadmill Lube Belt Message Horizon Fitness - Duur: 1:08. AC ERROR - (AC ERR) The control panel is not receiving the AC signal. 1. Steps to follow to determine and correct the problem. 2. ………………………………………………………………………… Err Code 01 through 18 - (Button Error) Indicates the keyboard membrane has a stuck key. Bypass the wire harness between the control panel circuit board and the power supply circuit board. navigate here

Tighten the motor mount screws. Distance window will display Pr-L (production limited mode). 4. Log in om ongepaste content te melden. i moved it and 10/14/2016 10/14/2016 Neil Nordic track c2300. http://www.fit-fix.com/pacemaster/P2-PS-PE-PC%20Detailed%20Error%20Messages.htm

Pacemaster Pro Plus Parts

Remove the 2 Isolator spacers and the 8 insulator bushings between the handlebar and the frame (See the ProSelect/ProElite owners manual page 5). 3. Taal: Nederlands Contentlocatie: Nederland Beperkte modus: Uit Geschiedenis Help Laden... Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. The problem could be the bracket is bent or the disc is dirty.

If the error is corrected, install the spare wire harness. Pressing Start/Stop will cause motor to run at 12% power - 12.0 will be displayed in the DATA window. In rare cases, the power supply or control panel may need to be replaced. 1. Pacemaster Pro Plus Treadmill Dead Sensor Insert the magnetic key, the software will be displayed in the Data Window. 2.

Replace the power supply. Bypass the wire harness between the control panel circuit board and the power supply circuit board. Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness.

Replace the power supply.

In very rare cases, a defective upper circuit board can cause this error and the circuit board will need to be replaced. Pacemaster Proselect Treadmill Manual If the error still occurs - 7. If the fuse is bad- 1. Step 2 Write down the displayed error code and the serial number located on the treadmill's front by the power cord if you receive an error message.

Pacemaster Pro Plus Treadmill Troubleshooting

Torque Pot Setting Procedure Caution: An insulated screwdriver MUST be used when adjusting the torque pot setting on the power supply. http://www.justanswer.com/fitness-equipment/3a75g-pacemaster-proplus-ii-moved-having.html Remove the magnetic key. Pacemaster Pro Plus Parts Je moet dit vandaag nog doen. Pacemaster Pro Plus Treadmill Owners Manual If the error still occurs - 4.

Volgende Treadmill Fail Compilation 2012 || ABC - Duur: 9:40. check over here Ask a Technician Not an Exercise Equipment Question? If the error still occurs - 2. Distance window will display Pr-F (production full mode). 6. Pacemaster Proplus Ii Error Code 31

PWM Test Mode This mode allows you to vary the power going to the drive motor between 1% and 100%. Remove the motor cover and loosen the four motor mount screws by turning them two turns each with the provided hex wrench. If the error is corrected, install the spare harness. his comment is here I have the Pro-Form Hybrid Trainer - the elliptical and 9/18/2016 9/18/2016 J.T.

Generated Sun, 23 Oct 2016 19:50:29 GMT by s_nt6 (squid/3.5.20) Pacemaster Pro Plus Rpm Sensor Replace the control panel circuit board. Error codes that display on the console signify what issue your machine may be experiencing.

That is if you received a good sensor.

Check the drive motor for continuity and shorts to ground. In the unlikely event that this does not correct the error - 3. Expert: treadmilltech replied6 years ago. Pacemaster Treadmill Error Code 24 If the fuse did not blow with the elevation motor disconnected, check the elevation motor and wiring between the power supply and the elevation motor for continuity and shorts to ground.

It should have a clear line of sight through it. STOP ERR - (StoP Err) Will occur when the tread belt takes more than 45 seconds to stop after the STOP or PAUSE key is pushed or the timer counts down Press the Incline UP button to raise the elevation up to 2 or 3 % elevation. weblink If the error is corrected, install the spare harness.

Obtaining Hours and Miles - ProClub LT The total hours will be displayed in the Time Window, total miles in the Distance Window every time you insert the magnetic key. Contact your PaceMaster dealer if you are unable to resolve the slippage issue. Remove the magnetic key. Although the result will be an ELE Err code since the elevation motor is disconnected, the fuse should be inspected.

Generated Sun, 23 Oct 2016 19:50:29 GMT by s_nt6 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection The error can be corrected by putting the control panel into the elevation test mode.