Home > Pacemaster Pro > Pacemaster Pro Plus Error Code 24

Pacemaster Pro Plus Error Code 24

Contents

The following section explains each one of these error codes and the steps that should be taken to correct the problem. Treadmill Aerobics PaceMaster Gold Elite Owner's Manual. Tommy: ‘Course it does. Check the connection where the optical sensor plugs into the power supply board. http://sisei.net/pacemaster-pro/pacemaster-error-code-31.html

Remember Me? Restart, this will be self-correcting. 4. LED Test Mode 1. The Distance Window will display Pr-F (production full mode). 5. Discover More

Pacemaster Pro Plus Parts

Välj språk. Du kan ändra inställningen nedan. treadmilltech is online now Pacemaster ProPlus II Error code 24 Resolved Question: Pacemaster ProPlus II Error code 24 Submitted: 5 years ago. Disconnect the elevation motor from the power supply.

RJ The Bike Guy 261 395 visningar 5:25 Läser in fler förslag ... I looked down and saw my treadmill walking belt was fraying to the left. You can check the for AC voltage output on the power supply. Pacemaster Pro Plus 2 Parts Torque Pot Setting Procedure Caution: An insulated screwdriver MUST be used when adjusting the torque pot setting on the power supply.

Logga in om du vill lägga till videoklippet i en spellista. Oct 21, 2013 | Treadmills 1 Answer I have a Pacemaster Gold treadmill that will not hold elevation. Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release. http://www.doityourself.com/forum/health-health-care-exercise-fitness/486698-problem-treadmill-pacemaster-proplus-ii-motor-controller.html Substitute a know good interconnect cable between the upper and lower PCAs to determineif the interconnect cable is defective.2.

Check the strobe disc holes for dust accumulation, if there is a build up of dust, clean out the holes. Pacemaster Pro Plus Treadmill Bad Relay Distance window will display Pr-L (production limited mode). 3. Pressing and holding the Calories button (for the ProClub use Pace Button) will cause all LED's to light and continuously sound the beeper. You can change this preference below.

Pacemaster Proselect Treadmill Manual

Touch the pause/enter button to access the quick start mode. http://www.fixya.com/support/t18877407-pacemaster_proselect_error_code_24 Error 31 is defined as faulty data received from lower PCA. Pacemaster Pro Plus Parts prev next 1 Points Related Questions: 1 Answer How to adjust tension belt on pacemaster proselect treadmill Tread Belt Tension Adjustment - Aerobics ProSelect ... Pacemaster Pro Plus Treadmill Owners Manual Transkription Det gick inte att läsa in den interaktiva transkriberingen.

What kind of service is that? http://sisei.net/pacemaster-pro/pacemaster-pro-plus-error-code-51.html Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual Nordic.X7i.NTL20909.pdf.... Treadmill no longer asks me for my weight, and I want to reset it. Remove the magnetic key. Pacemaster Pro Plus Rpm Sensor

Påminn mig senare Granska En sekretesspåminnelse från YouTube – en del av Google Hoppa över navigeringen SELadda uppLogga inSök Läser in ... Slowly turn the pot counter clock wise until the motor runs smoothly - the speed window should now read between 1.8 and 2.0. PDF Manual F80_F83_F85_S73_S77.pdf.... his comment is here Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release.

See Elevation Test Mode and follow steps 1-7 to clear the error code. Pacemaster Pro Plus Motor Please try the request again. If the error is corrected, install the spare harness.

an E2 is a speed error code and the others all just tell me you have a friction problem-elevate the incline up all the way,without mtr working,push yourself off backwards-did you

If the error still occurs -- 7. If I change the elevation setting it will go to Question about Gold Elite Treadmill Upper Console 1 Answer I have a 10 yr+ PaceMaster ProSelect Treadmill it ...PaceMaster ProSelect Treadmill It is usually followed by a dead sensor message when trying to restart. 1. Pacemaster Treadmill Manual This is the button test mode.

Share on Facebook Share on Twitter Share on Google+ Share on Pinterest Share by Email × Question about Treadmills Open Question Pacemaster proselect error code 24 Walking is ok, even at Hardcore Workouts 155 194 visningar 2:37 Sole F63 Problem - Take 2 - Längd: 4:17. This has proven to be a very frustrating and expensive experience, however it looks like it's hopefully going to resolve itself thanks to the guys at PaceMaster Service. weblink Aug 26, 2015 | Treadmills 1 Answer I have a 10 yr+ PaceMaster ProSelect Treadmill it works fine other than being stuck at its highest elevation.

The treadmill will start to run and the time in the Time Window will begin to count up from 0.00. It's been giving me an error code 24 indicating that there is a belt frozen error. In some cases the wire harness can cause the error code. In the unlikely event that this does not correct the error - 3.

The trouble shooting procedures forall of the are essentially the same. Stäng Läs mer View this message in English Du tittar på YouTube på Svenska. www.manualslib.com > ... > Treadmill > ProSelect > Owner's manual ... The interconnect cable at the upper PCA was mistakenly plugged into the CSAFE connector.3.

Go under the hood motor, and follow the step how to enter in the s. Otherwise, it would've been just $23 for shipping and $80 for the broken frame. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. Logga in om du vill lägga till videoklippet i en spellista.

was it diffacult? Arbetar ... On the contrary, Mike & Keith from PaceMaster Service (or more appropriately Pro-Fitness Services) answered my questions easily and with expertise. To post questions, help other DIYers and reduce advertising (like the one on your left), join our DIY community.

Err Code 24 - (Hi Acceleration Error) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. Have someone touch the up incline button, there should be a Voltage reading. If the error is corrected, install the spare harness. What should I do next?