Home > Pacemaster Pro > Pacemaster Pro Plus Error Code 30

Pacemaster Pro Plus Error Code 30

Contents

Replace the control panel circuit board. Question about Bronze Basic Treadmill 1 Answer Treadmill will not start up error comes up in window treadmill will not start up error comes up in window the tread mill powers If this does not correct the error, follow steps 1 through 3 as described above. Re-insert the magnetic key to resume normal operation Elevation Test Mode 1. http://sisei.net/pacemaster-pro/pacemaster-error-code-31.html

Nordic Track... After 2 seconds the Set Weight LED will begin to blink. 3. Detailed Error Message Descriptions & Test Modes Models - ProPlus II, ProSelect, ProElite, and ProClub LT PaceMaster treadmills have built in diagnostics that test various parts of the electronic system every Error Code 53 - Elevation Error 34 Second time out.

Pacemaster Treadmill Error Codes

Please try the request again. This may happen because the elevation motor is not running, the elevation potentiometer has failed or the elevation motor internal gears that drive the elevation potentiometer have stripped. Answer questions, earn points and help others Answer questions Manuals & User Guides PDF Manual Nordic.X7i.NTL20909.pdf....

The replacement sensor could be defective. Replace Membrane In some cases the wire harness can cause the error code. If the elevation fuse does not blow, re-connect the elevation motor, power up the treadmill and touch the incline up button. Pacemaster Pro Plus Parts Level 3 Expert 5327 Answers Matt Olenzek Level 2 Expert 286 Answers Atlanta Fitness Level 1 Expert 22 Answers Are you a Treadmills Expert?

If I change the elevation setting it will go to Question about ProPlus II Treadmill Incline Motor 1 Answer Treadmill magnetic key ...key I have lost the magnetic emergency key and Pacemaster Pro Plus 2 Error Code 31 Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release. Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. http://www.fixya.com/tags/pacemaster_treadmill_error_code_30 If the elevation does not raise up and the elevation fuse did not blow, touch the incline up button and listen for a click noise from the power supply.

At 12% power, the number in the speed window should be between 1.8 and 2.0. Pacemaster Pro Plus Treadmill Owners Manual Pressing Start/Stop will cause motor to run at 12% power - 12.0 will be displayed in the DATA window. or it's affiliates. Remove the magnetic key.

Pacemaster Pro Plus 2 Error Code 31

Err Code 43 and 44 - Replace the control panel circuit board. http://kao0w.rg.ro/d6 Please try the request again. Pacemaster Treadmill Error Codes Your cache administrator is webmaster. Pacemaster Pro Plus Treadmill Troubleshooting Replace the power cord.

If the fuse is blown, replace fuse and disconnect the elevation motor wire from power supply. http://sisei.net/pacemaster-pro/pacemaster-error-code-21.html The error message is as follows: Error Code Error message Definition of Error message ^ ^ ^ Err Code 21 - (Bad Relay) - Indicates malfunction of safety power relay on Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. Replace the power supply. Pacemaster Proselect Treadmill Manual

A loose connection on the power supply will cause this error code. Disconnect the elevation motor from the power supply. Insert magnetic key, software version will display in Data window. 2. his comment is here Err Code 20 - (Belt Error) This error will occur if the tread belt is moving while the magnetic key is inserted into the control panel to power up the treadmill.

Err Code 42 - (EE Error) - Upper circuit board problems. 1. Pacemaster Pro Plus Treadmill Dead Sensor VIRAL VIDEOS 1.851.103 προβολές 9:40 Understanding Error Codes on Treadmills - Διάρκεια: 1:01. Question about ProPlus Auto Treadmill Rear Roller 1 Answer I replaced the sensor on my Pacemaster Pro Plus Treadmill but I'm still getting a dead sensor error.

Remove the magnetic key.

Treadmill Doctor 37.362 προβολές 4:49 How To Reset the Treadmill Lube Belt Message Horizon Fitness - Διάρκεια: 1:08. This error can occur if the control panel receives a signal that the elevation is below zero. What should I do next? Pacemaster Pro Plus Rpm Sensor I replaced the sensor on my Pacemaster Pro Plus Treadmill but I'm still getting a dead sensor error.

ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection to 0.0.0.6 failed. Have someone touch the up incline button, there should be a Voltage reading. If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. http://sisei.net/pacemaster-pro/pacemaster-pro-plus-error-code-51.html There is an 8 wires cable, uses standard RJ45 connectors.

PDF Manual Treadmill.pdf. In my case, ... In some cases the wire harness can cause the error code. The following section explains each one of these error codes and the steps that should be taken to correct the problem.

Question about Treadmills 1 Answer Pacemaster pro plus error code 20 pacemaster pro plus error code 20 im receiving an erro code 20 on my treadmill If you wish to get