Pacemaster Pro Plus Error Code 31
Remove the 2 Isolator spacers and the 8 insulator bushings between the handlebar and the frame (See the ProSelect/ProElite owners manual page 5). 3. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question. In the unlikely event that this does not correct the error - 5. Replace the control panel circuit board.
Pacemaster Treadmill Error Codes
The following section explains each one of these error codes and the steps that should be taken to correct the problem. How? Contact your PaceMaster dealer if you are unable to resolve the slippage issue. Pacemaster Proselect Treadmill Manual If the elevation fuse does not blow, re-connect the elevation motor, power up the treadmill and touch the incline up button.
Troubleshooting a Treadmill That Won't Start What Is the Distance Around a Running Track for Each Lane? Pacemaster Pro Plus Treadmill Troubleshooting Question about Aerobics Pro Plus Walking Belt 1 Answer ERROR CODE 30 ON MY PACEMASTER PRO PLUS ERROR CODE 30 ON MY PACEMASTER PRO PLUS THE MOTOR WILL NOT COME UP Replace the control panel circuit board. Any advice?
Also, check to see that the disc is not bent or wobbly and that it is not making contact with the optical sensor. 4. Pacemaster Pro Plus Treadmill Owners Manual I called this guy about a specific problem MC 70 Treadmill Motor Controller MC70 - Home...but that doesn't seem to relate to your issue? Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT. Check the elevation motor and power supply wiring connections for a secure connection and signs of wear.
Pacemaster Pro Plus Treadmill Troubleshooting
Steps to follow to determine and correct the problem. 2. ………………………………………………………………………… Err Code 01 through 18 - (Button Error) Indicates the keyboard membrane has a stuck key. Clicking Here The error can be corrected by putting the control panel into the elevation test mode. Pacemaster Treadmill Error Codes Insert magnetic key, version will display in Data window. Pacemaster Pro Plus Treadmill Dead Sensor X Ask an Exercise Equipment Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 45 Exercise Equipment Technicians are Online Now Type Your Exercise Equipment Question Here...
Remember Me? http://sisei.net/pacemaster-pro/pacemaster-pro-plus-error-code-51.html Replace the drive motor. Err Code 26 - (High Speed Error) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. If there is no click noise from the power supply, the elevation relay(s) are not functioning. Pacemaster Pro Plus Parts
treadmilltech is online now I have a pacemaster proplus II - since I moved I am having Customer Question I have a pacemaster proplus II - since I moved I am If neither is the case contact pacemaster and order a new sensor. If the error still occurs - 6. his comment is here Look at your motor and there is a disc with holes in it mounted to the motor.
It should not be used as a substitute for professional medical advice, diagnosis or treatment. Pacemaster Pro Plus Rpm Sensor If I change the elevation setting it will go to Question about Gold Elite Treadmill Upper Console 1 Answer I have a 10 yr+ PaceMaster ProSelect Treadmill it ...PaceMaster ProSelect Treadmill Then select it.
If the error still occurs - 4.
TRAP ERROR - (trAP Err) - Follow the procedure for Bad Configuration below. Insert the magnetic key back into the control panel and do not touch any keys, if the error occurs, replace the keyboard membrane. 2. Advise user of proper operation of treadmill. 3. Pacemaster Treadmill Error Code 24 Have someone touch the up incline button, there should be a Voltage reading.
If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. Also, check the two wires on the optical sensor for any sign of damage, if the wires are damaged, replace the optical sensor. 5. Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. weblink Deze functie is momenteel niet beschikbaar.
Did you try the voltage check? PaceMaster includes a hex wrench to resolve problems involving the tread belt. In the unlikely event that this does not correct the error - 3. In some cases, the wire harness can cause the error code. 2.
Restart the treadmill, if the error still occurs - 2. Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release. Replace the power supply circuit board. Replace the fuse and retest.
If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three wire cord no longer than 12 feet. Replace as needed. 1. Replace the drive motor. Press the Incline UP button to raise the elevation up to 2 or 3 % elevation.
Ad Choices Login to DoItYourself Username: Password: Forgot username or password? Enter Your E-mail Address Enter Your First Name (optional) Then Don't worry — your e-mail address is totally secure. You can check the for AC voltage output on the power supply. Thanks for the question.
Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. Replace the control panel circuit board. I have the Pro-Form Hybrid Trainer - the elliptical and 9/18/2016 9/18/2016 J.T. Note: The steps outlined below assume that the error occurs within the first minute or two after startup.
Replace the circuit breaker.