Home > Pacemaster Pro > Pacemaster Pro Plus Error Code

Pacemaster Pro Plus Error Code

Contents

You can fine-tune the torque setting by following the procedure below. This may happen because the elevation motor is not running, the elevation potentiometer has failed or the elevation motor internal gears that drive the elevation potentiometer have stripped. If the error is corrected, install the spare harness. If the error still occurs: 2. http://sisei.net/pacemaster-pro/pacemaster-error-code-31.html

Insert magnetic key, version will display in Data window. 2. Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT. NOTE: in this mode, there is nothing to prevent the jamming of the nut at either end. Very rare: A power brownout during operation. http://www.fit-fix.com/pacemaster/P2-PS-PE-PC%20Detailed%20Error%20Messages.htm

Pacemaster Pro Plus Treadmill Troubleshooting

Replace the control panel. 8. The beeper will turn off 4 seconds after the raw potentiometer data is within the 48 to 244 range. 6. Is anyone out there???? Elevation Test Mode 1.

Distance window will display Pr-L (production limited mode). 4. The Time Window will display the raw potentiometer data, the Incline Window will display % elevation. Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices. Pacemaster Pro Plus Treadmill Dead Sensor Step 2 Write down the displayed error code and the serial number located on the treadmill's front by the power cord if you receive an error message.

Check the strobe disc holes for dust accumulation, if there is a build up of dust, clean out the holes. Err Code 20 - (Belt Error) This error will occur if the tread belt is moving while the magnetic key is inserted into the control panel to power up the treadmill. When you see the symbol About This Manual Important Safety Instructions Installation Requirements - - - - - - - - - - Unpacking our Treadmill - - - - -

Retest. 2.

Generated Sun, 23 Oct 2016 21:53:52 GMT by s_wx1196 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection Pacemaster Proselect Treadmill Manual Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices. Remove the magnetic key. If the error is corrected, install the spare harness.

Pacemaster Pro Plus Parts

Bypass the wire harness between the control panel circuit board and the power supply circuit board. More hints Fit 2 Run 14,701 views 1:01 PaceMaster Treadmills - Duration: 4:42. Pacemaster Pro Plus Treadmill Troubleshooting What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Pacemaster Pro Plus 2 Error Code 31 Do not remove the key to end the workout program.

If this does not correct the error, follow steps 3 through 7 as described below. 3. http://sisei.net/pacemaster-pro/pacemaster-error-code-21.html Loading... increments) Elevation Range - 0 to 15% grade (.5% increments) Operating Temperature Range - 50° to 100° F Maximum Permitted Weight - 300 lbs. © Aerobics, Inc. 1995 PaceMaster is a Replace the control panel circuit board. Pacemaster Pro Plus Treadmill Owners Manual

Press the Incline UP button to raise the elevation up to 2 or 3 % elevation. If the error still occurs- Replace the wiring harness. Retest. 2. his comment is here The speedometer isn't 10/2/2016 10/2/2016 J.T.

In very rare cases, a defective upper circuit board can cause this error and the circuit board will need to be replaced. Pacemaster Pro Plus Rpm Sensor Autoplay When autoplay is enabled, a suggested video will automatically play next. Replace the power supply.

Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT.

If the error occurs well into the program and does not occur each time the treadmill is used, skip to step 4. 1. Bypass the wire harness between the control panel circuit board and the power supply circuit board. Please try the request again. Pacemaster Pro Plus 2 Parts Tomahawk DIY 12,695 views 16:25 Pace master Excesive noise problems - Duration: 1:30.

X Ask an Exercise Equipment Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 45 Exercise Equipment Technicians are Online Now Type Your Exercise Equipment Question Here... Check the wire harness for continuity, shorts or damage. Replace the control panel circuit board. http://sisei.net/pacemaster-pro/pacemaster-pro-plus-error-code-51.html Check the elevation fuse on the power supply.

If the error still occurs - 5. If the error is corrected, install the spare wire harness. eHowFitness 6,235 views 1:51 Sole F80 LS1 Error - Duration: 3:17. Sign in to report inappropriate content.

One routine can be stored in each of the four custom memory positions. After 2 seconds Set Weight LED will begin to blink. 2. The material appearing on LIVESTRONG.COM is for educational use only. When you see the symbol damage to your treadmill.

Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. Page 2: Grounding Instructions Congratulations on the purchase of your PaceMaster Treadmill. If the error occurs well into the program and does not occur each time the treadmill is used, skip to step 4. 1. If the error still occurs - 3.