Home > Pacemaster Pro > Pacemaster Pro Plus Hr Error Codes

Pacemaster Pro Plus Hr Error Codes

Contents

Re-insert the magnetic key. If the error still occurs - 4. Please read this manual in its entirety before attempting to use your treadmill. Replace the power supply circuit board. http://sisei.net/pacemaster-pro/pacemaster-pro-plus-2-error-codes.html

If the fuse is bad- 1. If the error is corrected, install the spare harness. Replace the fuse and retest. Do not stand on the belt. http://www.fit-fix.com/pacemaster/P2-PS-PE-PC%20Detailed%20Error%20Messages.htm

Pacemaster Pro Plus Parts

If the error still occurs - 3. If the fuse blows again, disconnect the elevation motor wire harness from the power supply. It is important that you follow the steps in the order that they are listed to properly determine and correct the problem. If the error is corrected, install the spare harness.

Pacemaster pro plus PaceMaster Pro-Plus - Treadmills - · Cardio and Interval programs· custom designed phenolic deck· shock-absorbing elastomer cushions· Create up to four of your. Below are instructions on how to wear the chest strap. If the problem still occurs- 2. Pacemaster Pro Plus Treadmill Dead Sensor In some cases, the wire harness can cause the error code. 2.

This error code can occur at start up or during the workout. 1. Pacemaster Pro Plus Treadmill Owners Manual After 2 seconds Set Weight LED will begin to blink. 3. Understanding the PaceMaster Control Panel... https://www.manualslib.com/manual/633616/Pacemaster-Pro-Plus-Hr.html This information will be in bold print and marked by the symbols below.

In the unlikely event that this does not correct the error - 5. Pacemaster Pro Plus Rpm Sensor This indication will appear between five to eight seconds after the start button is pressed. 1. Err Code 31 - (Dead Sensor) Indicates that the control panel is not sensing movement of the drive motor. In the unlikely event that this does not correct the error - 3.

Pacemaster Pro Plus Treadmill Owners Manual

Use the hex wrench to turn the drive-belt adjustment screw in the treadmill's front end a half-turn clockwise. If the error still occurs - 4. Pacemaster Pro Plus Parts Failure to do so may result in personal injury or you will find useful suggestions related to the section in which it appears. Pacemaster Treadmill Error Codes PaceMaster Pro Plus - User review: 5 stars. "Well worth the money if you're even semi-serious about a treadmill" Pros: Stable, powerful, reliable Cons.

This problem is corrected by replacing the upper circuit board. "ERR" in Incline Window/1.0 in Speed Window upon power up. check over here The system returned: (22) Invalid argument The remote host or network may be down. The following section explains each one of these error codes and the steps that should be taken to correct the problem. Check the elevation motor and power supply wiring connections for a secure connection and signs of wear. Pacemaster Pro Plus 2 Error Code 31

The material appearing on LIVESTRONG.COM is for educational use only. The treadmill will start to run and the time in the Time Window will begin to count up from 0.00. It has its few draw backs but other than that it is great. his comment is here Replace the control panel circuit board.

Your cache administrator is webmaster. Pacemaster Proselect Treadmill Manual Page 8 For example a 3.5% incline is displayed as "E 3.5". IF THERE IS MOTOR MOVEMENT, check the optical sensor assembly and wiring for damage and for proper connection to the power supply.

Do not remove the key to end the workout program.

Replace the power supply circuit board. If the error still occurs - 2. Page 6 .5 percent change per press of the button. Pacemaster Pro Plus Treadmill Bad Relay Hook up the probes from a volt meter to the middle pin and the top pin on the jack.

Torque Pot Setting Procedure Caution: An insulated screwdriver MUST be used when adjusting the torque pot setting on the power supply. If the error is corrected, install the spare wire harness. Press the Incline UP button to raise the elevation up to 2 or 3 % elevation. weblink If the error is corrected, install the spare harness.

If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. When you see the symbol About This Manual Important Safety Instructions Installation Requirements - - - - - - - - - - Unpacking our Treadmill - - - - - Sign In Upload Page of 19 Go Download TroubleshootingTroublesh.. References PaceMaster: Gold Elite VR Treadmill PaceMaster: Gold Elite VR Owner's Manual TreadmillDoctor.com: Pacemaster Treadmill Reviews Comments Advertisement PEOPLE ARE READING The Controls Are Not Working on a NordicTrack Treadmill Comments

Please read this manual in its entirety before attempting to use your treadmill. Bypass the wire harness between the control panel circuit board and the power supply circuit board. You can fine-tune the torque setting by following the procedure below.