Home > Pacemaster Pro > Pacemaster Pro Plus Ii Error Code 31

Pacemaster Pro Plus Ii Error Code 31

Contents

If this does not correct the error, follow steps 1 through 3 as described above. Bypass the wire harness between the control panel circuit board and the power supply circuit board. mpopov69 28.244 weergaven 13:33 Doubleclickittofixit does electronics repairs...even on a treadmill motor control board... - Duur: 3:48. This information is displayed for 1-2 seconds. http://sisei.net/pacemaster-pro/pacemaster-error-code-31.html

Retest. 2. I have a nordictrack ACT pro elliptical. Login|Contact Us Exercise Equipment Exercise Equipment Repair Questions? characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 126 10817633 Login|Contact Us Exercise Equipment Exercise Equipment Repair Questions?

Pacemaster Treadmill Error Codes

If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. The following section explains each one of these error codes and the steps that should be taken to correct the problem. Insert magnetic key, software version will display in Data window. 2.

Power up the treadmill and touch the incline up button. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Replace as needed. Pacemaster Proselect Treadmill Manual Why pacemaster doesn't have the codes listed in the manual or on their web site is frustrating.

Nordic Track... Pacemaster Pro Plus Treadmill Troubleshooting HI ACC ERR - (Hi ACC Err) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. Insert magnetic key, version will display in Data window. http://www.fit-fix.com/pacemaster/Pro-Plus_Detailed_Error_Messages030100.htm IF THERE IS NO MOTOR MOVEMENT, check the wiring between the power supply circuit board and the drive motor for good connection shorts to ground and continuity. 2.

After reading this article, do you think buyers should purchase this treadmill? Pacemaster Pro Plus Rpm Sensor Touch the incline down button to bring the elevation back down to zero percent. 7. Replace the power supply circuit board. RACE ERROR - (rAcE Err) Indicates too high an acceleration rate during initial startup. 1.

Pacemaster Pro Plus Treadmill Troubleshooting

Steps to follow to determine and correct the problem. 2. ………………………………………………………………………… Err Code 01 through 18 - (Button Error) Indicates the keyboard membrane has a stuck key. her latest blog Restart the treadmill, if the error still occurs - 2. Pacemaster Treadmill Error Codes Bezig... Pacemaster Pro Plus Treadmill Dead Sensor Check the strobe disc holes for dust accumulation, if there is a build up of dust, clean out the holes.

If there is no movement from the elevation mechanism, check the fuse on the power supply circuit board (See Power Supply Replacement). http://sisei.net/pacemaster-pro/pacemaster-pro-plus-error-code-51.html The most likely problem is a broken connection in the elevation potentiometer harness or a loose connecter. Check my pricing, ongoing promotions, manufacturer, mark and model, etc then make a decision. If the error is corrected, install the spare wire harness. Pacemaster Pro Plus Parts

Insert magnetic key, version will display in Data window. 2. Ask a Technician Not an Exercise Equipment Question? Also, check to see that the disc is not bent or wobbly and that it is not making contact with the optical sensor. 4. weblink Replace the control panel circuit board. 4.

Pressing Incline up or down buttons will move unit up or down. Pacemaster Pro Plus Treadmill Owners Manual Gepubliceerd op 1 sep. 2015Pacemaster Treadmill Error Code 31 Categorie Mensen & blogs Licentie Standaard YouTube-licentie Meer weergeven Minder weergeven Laden... Hook up the probes from a volt meter to the middle pin and the top pin on the jack.

Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release.

Replace the power supply. Use the STOP key or let the time countdown to 0. 2. Deze functie is momenteel niet beschikbaar. Pacemaster Treadmill Error Code 24 Replace the drive motor.

BELT ERROR - (bELt Err) This error will occur if the tread belt is moving while the magnetic key is inserted into the control panel to power up the treadmill. 1. I would think it is in the sensor. At 12% power, the number in the speed window should be between 1.8 and 2.0. check over here Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices.

try to turn off the machine. On the power supply (see figure 2, part number 14) insert the screwdriver into the pot and gently turn the torque pot all the way counter clock wise, then very slowly You may freely link to this site, and use it for non-commercial use subject to our terms of use. Re-insert the magnetic key.

Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. BAD CONFIGURATION - (bAd Con Fig) - Upper circuit board problems. 1. LED Test Mode 1. Toevoegen aan Wil je hier later nog een keer naar kijken?

If the elevation fuse does not blow, re-connect the elevation motor, power up the treadmill and touch the incline up button. Torque Pot Setting Procedure Caution: An insulated screwdriver MUST be used when adjusting the torque pot setting on the power supply. NOTE: in this mode, there is nothing to prevent the elevation nut from jamming at either the top or bottom. Do not use a power strip.

In the unlikely event that this does not correct the error - 5. Bypass the wire harness between the control panel circuit board and the power supply circuit board.