Home > Pacemaster Pro > Pacemaster Pro Plus Treadmill Error Codes

Pacemaster Pro Plus Treadmill Error Codes

Contents

Kies je taal. The following section explains each one of these error codes and the steps that should be taken to correct the problem. After 2 seconds the Set Weight LED will begin to blink. 3. Err Code 30 - (Gone Sensor) During operation, if the control panel looses the speed sensor signal, this error will occur. navigate here

IF THERE IS MOTOR MOVEMENT, check the optical sensor assembly and wiring for damage and for proper connection to the power supply. Bypass the wire harness between the control panel circuit board and the power supply circuit board. X Ask an Exercise Equipment Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 45 Exercise Equipment Technicians are Online Now Type Your Exercise Equipment Question Here... Toevoegen aan Wil je hier later nog een keer naar kijken?

Pacemaster Pro Plus Treadmill Dead Sensor

References PaceMaster: Gold Elite VR Treadmill PaceMaster: Gold Elite VR Owner's Manual TreadmillDoctor.com: Pacemaster Treadmill Reviews Comments Advertisement PEOPLE ARE READING The Controls Are Not Working on a NordicTrack Treadmill Comments If the error still occurs - 7. When the computer determines a problem, the treadmill automatically shuts down and an error code is displayed on the control panel.

Alternatively, the main wire harness connection may be intermittent. Page 7 • MAGNETIC SAFETY KEY - The magnetic safety key with its red cord and garment clip is a safety feature of the PaceMaster. If the error is corrected, install the spare harness. Pacemaster Pro Plus Rpm Sensor Later herinneren Nu bekijken Conform de wetgeving ten aanzien van de bescherming van gegevens verzoeken we je even de tijd te nemen om de belangrijkste punten van ons Privacybeleid door te

in. Pacemaster Pro Plus Parts The Data Window will display oFF. Tightening the drive belt adjustment screw more than 1 1/2 turns can result in bearing damage to the motor and/or drive roller. my review here If the error still occurs replace the control panel circuit board with updated software chip. 5.

Reconnect the wire harness and the elevation potentiometer to the power supply and restart. Pacemaster Treadmill Error Code 24 See Elevation Test Mode and follow steps 1-7 to clear the error code. The error message is as follows: Error Code Error message as displayed on the Control Panel Definition of Error message description ^ ^ ^ BAD RELAY - (bAd rEL Ay) - i moved it and 10/14/2016 10/14/2016 Neil Nordic track c2300.

Pacemaster Pro Plus Parts

Re-insert the magnetic key to resume normal operation. https://www.manualslib.com/manual/633616/Pacemaster-Pro-Plus-Hr.html Error Code 53 - Elevation Error 34 Second time out. Pacemaster Pro Plus Treadmill Dead Sensor Replace the control panel circuit board. 4 External electrical noise (AC line noise) can interfere with the (RPM) signal between the power supply and the control panel. Pacemaster Proselect Treadmill Manual Also, check the two wires on the optical sensor for any sign of damage, if the wires are damaged, replace the optical sensor. 5.

Error codes that display on the console signify what issue your machine may be experiencing. http://sisei.net/pacemaster-pro/pacemaster-proplus-ii-treadmill-error-codes.html If the error is corrected, install the spare harness. Sign up! Page 15 weight entered, by pressing the INCREASE (CALORIES) or DECREASE (AEROBIC POINTS) buttons adjust the weight to your weight, now press the ENTER (HEART RATE). 3. Pacemaster Pro Plus Treadmill Owners Manual

Disconnect the elevation motor from the power supply. Login|Contact Us Exercise Equipment Exercise Equipment Repair Questions? Deze functie is momenteel niet beschikbaar. his comment is here brh54321 116 weergaven 1:17 TREADMILL ERROR - VEDA 2011 #8 4-8-11 - Duur: 2:43.

If a problem occurs, PaceMaster can be stopped quickly by pulling on the red safety cord to remove the magnetic key from the control panel. Pacemaster Pro Plus 2 Parts Laden... This chest strap must be used when using the heart rate control program.

The Time Window will display the raw potentiometer data, the Incline Window will display % elevation.

Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. Replace the power supply. Ask treadmilltech Your Own Question treadmilltech, Technician Category: Exercise Equipment Satisfied Customers: 5645 Experience: 20+ years experience repairing exercise equipment with emphasis on Nordictrack/Proform and Horizon 32169475 Type Your Exercise Equipment Pacemaster Pro Plus Treadmill Bad Relay Re-insert the magnetic key and resume normal operation.

Volgende Treadmill Fail Compilation 2012 || ABC - Duur: 9:40. Your cache administrator is webmaster. If the fuse did not blow with the elevation motor disconnected, check the elevation motor and wiring between the power supply and the elevation motor for continuity and shorts to ground. weblink increments) Elevation Range - 0 to 15% grade (.5% increments) Operating Temperature Range - 50° to 100° F Maximum Permitted Weight - 300 lbs. © Aerobics, Inc. 1995 PaceMaster is a

Page 11: Using Pacemaster For The First Time • Check that the elastic strap has not loosened during exercise. • Make sure that the electrodes on the transmitter are moistened. Re-insert the magnetic key to resume normal operation Elevation Test Mode 1. Log in om je mening te geven. If this does not correct the problem- 1.

Press and hold simultaneously Calories and Aerobic Points buttons (for the ProClub use the Level+ & Level- Buttons) until unit beeps. Step 5 Unplug the treadmill and check that the drive motor connection and ceramic fuse are securely attached and do not show signs of wear if you receive error code 425. Pressing Incline up or down buttons will move unit up or down. Beoordelingen zijn beschikbaar wanneer de video is verhuurd.