Home > Pacemaster Pro > Pacemaster Proplus Error Codes

Pacemaster Proplus Error Codes

Contents

If this does not correct the error, follow steps 1 through 3 as described above. Turn the left and right tread belt screws located on the back of the treadmill a half-turn clockwise. Also make sure the disc is passing straight through the middle of the sensor. Press and hold simultaneously Calories and Aerobic Points buttons (for the ProClub use the Level+ & Level- Buttons) until unit beeps. http://sisei.net/pacemaster-pro/pacemaster-proplus-ii-error-codes.html

FreeMotion 790... Err Code 42 - (EE Error) - Upper circuit board problems. 1. It should not be used as a substitute for professional medical advice, diagnosis or treatment. Replace the power supply circuit board. http://www.fit-fix.com/pacemaster/P2-PS-PE-PC%20Detailed%20Error%20Messages.htm

Pacemaster Pro Plus Treadmill Troubleshooting

Things You'll Need Hex wrench Magnetic key Related Searches THE LIVESTRONG.COM MyPlate Nutrition, Workouts & Tips GOAL Gain 2 pounds per week Gain 1.5 pounds per week Gain 1 pound per Equipment (95xi ) has a knock sound whilst peddling. 9/19/2016 9/19/2016 J.T. ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed. How JustAnswer Works: Ask an Expert Experts are full of valuable knowledge and are ready to help with any question.

Pressing Incline up or down buttons will move unit up or down. GONE SENSOR - (gonE SenSor) During operation, if the control panel looses the motor speed signal, this error will occur. Err Code 24 - (Hi Acceleration Error) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate. Pacemaster Pro Plus Treadmill Dead Sensor If the error occurs well into the program and does not occur each time the treadmill is used, skip to step 4. 1.

Replace if needed. 3. Replace as needed. 1. The error can be corrected by putting the control panel into the elevation test mode.

Remove the motor cover and loosen the four motor mount screws by turning them two turns each with the provided hex wrench.

Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT. Pacemaster Proselect Treadmill Manual If the fuse is blown, replace fuse and disconnect the elevation motor wire from power supply. I called this guy about a specific problem MC 70 Treadmill Motor Controller MC70 - Home...but that doesn't seem to relate to your issue? Check to make sure the sensor is plugged in to the board and in itself.

Pacemaster Pro Plus 2 Error Code 31

PWM Test Mode This mode allows you to vary the power going to the drive motor between 1% and 100%. http://www.justanswer.com/fitness-equipment/76j93-getting-error-code-pacemaster-proplus-ii-treadmill.html PANEL 00 - 18 - (PAn EL 00 - 18) Indicates the keyboard membrane has a stuck key. Pacemaster Pro Plus Treadmill Troubleshooting If there is no click noise from the power supply, the elevation relay(s) are not functioning. Pacemaster Pro Plus Parts Replace the control panel circuit board.

This information is displayed for 1-2 seconds. http://sisei.net/pacemaster-pro/pacemaster-proplus-error-31.html Replace the power supply. If the error still occurs - 6. BAD SCR - (bAd Scr) Indicates malfunction of the circuitry that controls motor speed. 1. Pacemaster Pro Plus Treadmill Owners Manual

Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices. If the error still occurs - 4. I have a Nordic track vr25 elite. http://sisei.net/pacemaster-pro/pacemaster-proplus-ii-treadmill-error-codes.html Wait for the tread belt to come to a complete stop before inserting the magnetic key to restart.

Question about Treadmills 1 Answer Pacemaster pro plus error code 20 pacemaster pro plus error code 20 im receiving an erro code 20 on my treadmill If you wish to get Pacemaster Pro Plus Rpm Sensor Is there a solution to bringing it back down to normal elevation. After 2 seconds Set Weight LED will begin to blink. 2.

If the wiring tests ok replace the sensor.

After 2 seconds Set Weight LED will begin to blink. 3. Problem with a treadmill (Pacemaster ProPlus ii)...motor controller? Check the connection where the optical sensor plugs into the power supply board. Pacemaster Pro Plus 2 Parts Do not use a power strip.

Use the STOP key or let the time countdown to 0. 2. error code 31 indicates there is a problem with the optical counter that relays how fast your treadmill is going .They are out of alignment. The speedometer isn't 10/2/2016 10/2/2016 J.T. weblink Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF.

Or just drag it here! Check the strobe disc holes for dust accumulation, if there is a build up of dust, clean out the holes. The speedometer isn't 10/2/2016 10/2/2016 J.T. If the error is corrected, install the new wire harness.

If the error still occurs: 2. Insert magnetic key, version will display in Data window. 2. How to Change Your Treadmill From KPH to MPH Bowflex TreadClimber vs. Replace the drive motor.

Replace the elevation motor. Check all wire connections between the power supply, elevation motor and control panel. 2. STOP ERR - (StoP Err) Will occur when the tread belt takes more than 45 seconds to stop after the STOP or PAUSE key is pushed or the timer counts down Replace the power supply. Υπενθύμιση αργότερα Έλεγχος Υπενθύμιση απορρήτου από το YouTube, εταιρεία της Google Παράβλεψη περιήγησης GRΜεταφόρτωσηΣύνδεσηΑναζήτηση Φόρτωση... Επιλέξτε τη γλώσσα σας. Κλείσιμο Μάθετε περισσότερα View this message in English

That is if you received a good sensor.