Home > Pacemaster Pro > Pacemaster Proselect Error Code 21

Pacemaster Proselect Error Code 21

Contents

it should be located near the front roller or mounted on the motor. The treadmill will not operate if plugged into a GFCI (Ground Fault Current Interrupt) outlet. Replace as needed. 3. Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness. http://sisei.net/pacemaster-pro/pacemaster-proselect-error-code-30.html

Error Code 52 - Elevation signal too fast This error occurs if the elevation signal to the control panel changes at too rapid a rate when requesting an elevation change. First, determine if the motor is turning before you get the E21 or not. After 2 seconds Set Weight LED will begin to blink. 2. Ask a Technician Not an Exercise Equipment Question? http://www.fit-fix.com/pacemaster/P2-PS-PE-PC%20Detailed%20Error%20Messages.htm

Pacemaster Pro Plus Treadmill Error Codes

Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. Check the speed sensor and strobe disc for damage (check the speed sensor and its connections). 2. Remove the magnetic key. Re-insert the magnetic key to resume normal operation Elevation Test Mode 1.

Err Code 20 - (Belt Error) This error will occur if the tread belt is moving while the magnetic key is inserted into the control panel to power up the treadmill. Remove the magnetic key. Please try the request again. Pacemaster Pro Plus Parts This error can occur if the elevation motor continues to run after 34 seconds.

If there is no click noise from the power supply, the elevation relay(s) are not functioning. Sign in 1 Loading... Fix Error Code 21 On Pacemaster Proselect Get Your Computer Running Normal Again in Under 15 Minutes Filed in Windows Error Code 21 On Pacemaster Proselect on Problem with Error Code http://www.justanswer.com/fitness-equipment/4i7op-pacemaster-treadmill-10-years-old-showing.html Press and hold simultaneously + and - buttons in Time window (for the ProClub use the Level+ & Level- Buttons) for 3 sec then release.

If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet. Pacemaster Pro Plus Treadmill Dead Sensor System Troubleshooterâ„¢ Troubleshoot System Problems If your PC has become severely unstable, it can be hard for you to know where to start with repairs. Your cache administrator is webmaster. Posted on Nov 06, 2010 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Add Your Answer Tips for a great

Pacemaster Proselect Treadmill Manual

Note: The steps outlined below assume that the error occurs within the first minute or two after startup. Loading... Pacemaster Pro Plus Treadmill Error Codes The Distance Window will display Pr-F (production full mode). 5. Pacemaster Pro Plus Treadmill Troubleshooting This is usually caused by a stuck elevation relay on the power supply board or a damaged or shorted wire harness.

Published on Sep 1, 2015Pacemaster Treadmill Error Code 31 Category People & Blogs License Standard YouTube License Show more Show less Loading... check over here It is important that you follow the steps in the order that they are listed to properly determine and correct the problem. My Account Log In TOLL FREE 8am - 5pm Mon - Fri CST 800-750-4766 Items in cart 0 Total amount $0.00 Home Parts reviews repair help customer service blog Forum (0 If the elevation fuse blows, the power supply is shorted and will need to be replaced. Pacemaster Pro Plus Treadmill Owners Manual

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Also, check the two wires on the optical sensor for any sign of damage, if the wires are damaged, replace the optical sensor. 5. NOTE: in this mode, there is nothing to prevent the elevation nut from jamming at either the top or bottom. his comment is here Solution 4: Download Driver Update Tool to automate your Driver Updates If you know the device that is causing the driver errors, you can try to download updated drivers from the

Bypass the wire harness between the control panel circuit board and the power supply circuit board. Pacemaster Pro Plus Rpm Sensor Replace the power supply. Distance window will display Pr-L (production limited mode). 4.

If the error is corrected, install the spare wire harness.

Err Code 31 - (Dead Sensor) Indicates that the control panel is not sensing movement of the drive motor. In the unlikely event that this does not correct the error - 5. RTO Sole F80... Pacemaster Pro Plus 2 Parts Oct 23, 2016 | Reebok Treadmills 0 Answers How do you reinstall the "continue watching" function on youtube?

Posted on Sep 10, 2009 Helpful 0 Not Helpful Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images John Mazmanian 832 Answers SOURCE: Getting a evanboro 2,033 views 1:30 25 Laughable Treadmill Gym Fails - Duration: 4:20. Press the Incline UP button to raise the elevation up to 2 or 3 % elevation. weblink Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF.

I am attempting to upload it to www.manualsonline.com, so if you still want it, hopefully they will have it soon. Sign in Transcript Statistics 1,419 views 15 Like this video? It's worth a thousand words. Is treadmill plugged into the wall outlet?

Sign up! A danger of a fall and serious injury is always present. Go to HOOD open the cover motor and follow the steps indicated.