Home > Pacemaster Pro > Pacemaster Proselect Error Code 26

Pacemaster Proselect Error Code 26

Contents

If this does not correct the error, follow steps 1 through 3 as described above. I find it unlikely that both could be defective. Insert magnetic key, version will display in Data window. 2. View Most Popular ProPlus II Treadmill Control Panel With Membrane Treadmills Related Question I replaced the sensor on my Pacemaster Pro Plus Treadmill but I'm still getting a dead sensor error. http://sisei.net/pacemaster-pro/pacemaster-proselect-error-code-30.html

or it's affiliates. It was adjusted and not loose wasn't it? Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. Also, when it is taking off to runaway speed, is there a speed indication on the speedometer? see here

Pacemaster Treadmill Error Codes

Do not hold down any key for more than 5 seconds or this error will appear. 1. It basically monitors the sensor signal and verifies that it's appropriate for the requested speed. Have you checked to see that the cables are securely plugged in.

Advise user of proper operation of the treadmill. Generated Sun, 23 Oct 2016 23:58:07 GMT by s_wx1126 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.6/ Connection I have a Nordic track vr25 elite. Pacemaster Pro Plus Treadmill Owners Manual A 5.17 with mismatched upper and lower software.5.

ProPlus2/ProSelect/ProElite/ProClub LT Test Modes Button Test Mode 1. Pacemaster Proselect Treadmill Manual If the error still occurs -- 7. So should I just call PaceMaster and have them send me a new speed sensor? Incorrect adjustment of the speed sensor potentiometer (when equipped).

Craig,Can't remember if I pushed Reply. Pacemaster Pro Plus Parts Locate the speed sensor potentiometer (when equipped) on the lower PCA. Damaged speed sensor target. Torque Pot Setting Procedure Caution: An insulated screwdriver MUST be used when adjusting the torque pot setting on the power supply.

Pacemaster Proselect Treadmill Manual

If there is, the problem is in the elevation motor, wiring, or a bad connection between the power supply and elevation motor. In most cases, replacing the optical sensor assembly will correct the problem. 2. Pacemaster Treadmill Error Codes What should I do next? Pacemaster Pro Plus 2 Error Code 31 If the error still occurs - 5.

If unit has a magnetic speed sensor, the gap between the end of the sensor and the flywheel tooth needs to be 3/16". check over here Alternatively, the main wire harness connection may be intermittent. The Data Window will display oFF. Submitted: 6 years ago. Pacemaster Pro Plus Treadmill Troubleshooting

If the error still occurs: 2. Carefully adjust the speed sensor potentiometer until the treadmill is operating the smoothest. If the error still occurs -- 6. his comment is here There is a small chance that the board is bad, but more likely the sensor has failed.

If elevation does not raise up, check the elevation fuse, if it blew, the elevation motor is shorted and will need to be replaced. Pacemaster Pro Plus Treadmill Dead Sensor Replace the 5.17 upper and lower software with the most current software versions.4. Jan 14, 2015 | PaceMaster ProPlus Auto Treadmill Rear... 1 Answer Pacemaster pro plus Usually dirt build up.

If the error occurs well into the program and does not occur each time the treadmill is used, skip to step 4. 1.

X Ask an Exercise Equipment Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 57 Exercise Equipment Technicians are Online Now Type Your Exercise Equipment Question Here... Include an image. Insert magnetic key, software version will display in Data window. 2. Pacemaster Pro Plus Rpm Sensor The speedometer isn't 10/2/2016 10/2/2016 J.T.

The system returned: (22) Invalid argument The remote host or network may be down. The chrome plate has small (half inch) holes all around it's perimeter. During operation someone fell on to the 10/8/2016 10/8/2016 J.T. weblink It is usually followed by a dead sensor message when trying to restart. 1.

These two adjustments are typically small and are generally only a matter of fine tuning. I have to actually use my foot to get the belt started, and when I do and it goes off to the races, the red light (which is right next to Fit 2 Run 14.701 προβολές 1:01 Treadmill Walking Belt Installation Video by Treadmill Doctor - Διάρκεια: 36:10. Touch the pause/enter button to access the quick start mode.

The beeper will turn off 4 seconds after the raw data is within the 48 to 244 range. 7. Watch my video on youtube and you will get an idea of what to look for. Damaged speed sensor target. Increase the speed to full speed and again adjust the speed sensor potentiometer until the treadmill is operating the smoothest.