Home > Pacemaster Pro > Pacemaster Proselect Error Code List

Pacemaster Proselect Error Code List

Contents

LED Test Mode 1. Replace the power supply circuit board. Press the CALORIES button for the total caloric expenditure and the AEROBIC POINTS button for the total points you will earn. Replace as needed. http://sisei.net/pacemaster-pro/pacemaster-proselect-error-code-20.html

Holding the motor cover level and waist high, tilt it 45 degrees by lowering your left hand. This error can occur if the elevation motor continues to run after 34 seconds. He's very knowledgeable about all brands and their problems. Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness.

Pacemaster Pro Plus Treadmill Error Codes

Check the wire harness for continuity, shorts or damage. The error can be corrected by putting the control panel into the elevation test mode. Page 6: Grounding Instructions, Assembly Grounding Instructions DANGER: This product must be properly grounded.

In the unlikely event that this does not correct the error - 2. This problem is corrected by replacing the upper circuit board. "ERR" in Incline Window/1.0 in Speed Window upon power up. This may happen because the elevation potentiometer wire harness has lost continuity or the elevation potentiometer itself has failed. Pacemaster Pro Plus Parts Bypass the wire harness between the control panel circuit board and the power supply circuit board with a spare wire harness.

Pressing Start/Stop will cause motor to run at 12% power - 12.0 will be displayed in the DATA window. Pacemaster Pro Plus Treadmill Troubleshooting You can check the for AC voltage output on the power supply. Hey, thanks. If an extension cord is needed, it must be a heavy-duty 14-guage, grounded three-wire cord no longer than 12 feet.

Your theoretical maximum heart rate is determined by subtracting your age from 220, which is the closest approximation of the average person’s heart rate. Pacemaster Treadmill Error Code 24 Error Code 52 - Elevation signal too fast This error occurs if the elevation signal to the control panel changes at too rapid a rate when requesting an elevation change. ELEVATION ERROR - (ELE Err) - Indicates the control panel has not sensed an elevation change that was requested. Replace if needed. 3.

Pacemaster Pro Plus Treadmill Troubleshooting

Equipment (95xi ) has a knock sound whilst peddling. 9/19/2016 9/19/2016 J.T. try here If elevation does not raise up, check the elevation fuse, if it blew, the elevation motor is shorted and will need to be replaced. Pacemaster Pro Plus Treadmill Error Codes If the error still occurs - 2. Pacemaster Proselect Treadmill Manual This is the button test mode.

Check the elevation motor and wiring for continuity and shorts to ground. check over here NOTE: in this mode, there is nothing to prevent the jamming of the nut at either end. When the black adjustment knob is positioned as far forward as possible (toward the front of the treadmill) the deck cushioning is in the softest position. Page 11: Operating Instructions, Setting Your Weight And Age, Metric Units, Wireless Chest Strap Transmitter Adjust to the correct weight. Pacemaster Pro Plus Treadmill Dead Sensor

STOP ERR - (StoP Err) Will occur when the tread belt takes more than 45 seconds to stop after the STOP or PAUSE key is pushed or the timer counts down This indication will appear between five to eight seconds after the start button is pressed. 1. Bypass the wire harness between the control panel circuit board and the power supply circuit board. his comment is here Replace the power supply.

Page 21: Heartsmart™ Pulse Monitoring System, Heart Rate Zone Bar, On-target Indicator, Performance Review, Exercise Preview The ProSelect and the ProElite use the age-adjusted formula to calculate your training zone. Pacemaster Pro Plus Treadmill Owners Manual Very rare: A power brownout during operation. Also, check the wire harness for shorts and/or damage.

If the error is corrected, install the spare wire harness.

In some cases the wire harness can cause the error code. BGAReflow 18.430 προβολές 3:48 Troubleshoot a Broken Treadmill That Won't Run - Διάρκεια: 16:25. Disconnect the elevation motor from the power supply. Pacemaster Pro Plus Rpm Sensor Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT.

Restart, this will be self-correcting. 4. Press Enter (for the ProClub use the Select Button) button. Treadmill Doctor 24.960 προβολές 3:00 Treadmill Troubleshooting: Treadmill Speed Fluctuation Problems - Treadmill Doctor - Διάρκεια: 3:49. http://sisei.net/pacemaster-pro/pacemaster-proselect-error-code-30.html If the error is corrected, install the spare harness.

Reconnect the wire harness and the elevation potentiometer to the power supply and restart. To print the manual completely, please, download it. You can fine-tune the torque setting by following the procedure below. Replace the power supply circuit board.

Bypass the wire harness between the power supply and the control panel with a spare harness. If the error still occurs replace the control panel circuit board. 3. CAUTION: Be sure to unplug your treadmill before attempting any cleaning or maintenance. Not only did you buy one of the highest quality treadmills on the market; you also received excellent value for your dollar.

After 2 seconds Set Weight LED will begin to blink. 3. It's free! Page 3: Introduction INTRODUCTION Congratulations on your commitment toward better health and fitness! The following pages give you step-by-step instructions on how to use each program.

If the error is not corrected- 3.