Home > Pacemaster Pro > Pacemaster Treadmill Error Code 31

Pacemaster Treadmill Error Code 31

Contents

Check the drive motor for continuity and shorts to ground. The error can be corrected by putting the control panel into the elevation test mode. After 2 seconds Set Weight LED will begin to blink. 3. it is worth buying I have had mine between 10 and 15 years and still runs great Had mine a long time. his comment is here

Great! Make sure the treadmill is plugged into a 20 AMP DEDICATED CIRCUIT. After scanning my PC using RegCure, I can confirm that Pacemaster Proselect Error Code 31 Treadmill did not return. Protein Fart 879,718 views 4:20 Troubleshoot a Broken Treadmill That Won't Run - Duration: 16:25.

Pacemaster Treadmill Error Code 24

See Elevation Test Mode and follow steps 1-7 to clear the error code. DescriptionErrors 30 through 33 all indicate the loss of communications or erratic communications ... In the unlikely event that this does not correct the error - 4. Your cache administrator is webmaster.

It will go to the proper elevation and then immediately start descending. Why pacemaster doesn't have the codes listed in the manual or on their web site is frustrating. If the error still occurs - 4. Pacemaster Pro Plus Treadmill Troubleshooting If the error is corrected, install the spare harness.

Error Code 50 - Elevation Error is out of range. Pacemaster Proselect Treadmill Parts Check my pricing, ongoing promotions, manufacturer, mark and model, etc then make a decision. Press and hold simultaneously the + and - buttons in the Time Window for 3 seconds then release. Finally, I got into a good training zone and have been using my treadmill for over 3 years approx 5 times per week 66 minutes per session, and my wife also

Retest. 2. Pacemaster Pro Plus Parts When the computer determines a problem, the treadmill automatically shuts down and an error code is displayed on the control panel. Err Code 43 and 44 - Replace the control panel circuit board. Restart, this will be self-correcting. 4.

Pacemaster Proselect Treadmill Parts

Up next Bodyguard Fitness Treadmills (2012+) Error 53 - Duration: 6:11. http://pcrepairpro15.com/pacemaster-proselect-error-code-31-treadmill.php Check the connection where the optical sensor plugs into the power supply board. Pacemaster Treadmill Error Code 24 Enter A Title Tell Us Your Opinion! [ ? ] Close Help Entering your contribution is easy to do. Pacemaster Pro Plus Treadmill Dead Sensor Err Code 24 - (Hi Acceleration Error) Indicates that the control panel is receiving erratic motor speed signals or too high an acceleration rate.

My treadmill no longer asks me for my weight, and I'd like to reset it. this content This error can occur if the control panel receives a signal that the elevation is below zero. Loading... Insert magnetic key, software version will display in Data window. 2. Pacemaster Proselect Treadmill Manual

In most cases, replacing the optical sensor assembly will correct the problem.2. Sign In Register Categories Recent Discussions Activity Categories 203 All Categories84 General 11 General Discussion 103 Treadmills 5 Hot Deals on Treadmills 12 Questions About Buying A Treadmill 3 Treadmills For If neither is the case contact pacemaster and order a new sensor. weblink Click 'Start Scan' to scan your PC for errors If errors are found, click 'Next' then 'Repair Now' to Repair the problem You may need to reboot your PC for the

Press and hold simultaneously Calories and Aerobic Points buttons (for the ProClub use the Level+ & Level- Buttons) until unit beeps. Pacemaster Pro Plus Treadmill Owners Manual This indication will appear between five to eight seconds after the start button is pressed.1. Generated Sun, 23 Oct 2016 21:56:04 GMT by s_wx1196 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection

Click here to add your own comments Join in and write your own page!

In some cases the wire harness can cause the error code. Question about Treadmills 1 Answer Pacemaster pro plus error code 20 pacemaster pro plus error code 20 im receiving an erro code 20 on my treadmill If you wish to get The majority of these issues might have many achievable triggers as well. Pacemaster Pro Plus 2 Parts Enter Your E-mail Address Enter Your First Name (optional) Then Don't worry — your e-mail address is totally secure.

Steps to follow to determine and correct the problem. 2. ………………………………………………………………………… Err Code 01 through 18 - (Button Error) Indicates the keyboard membrane has a stuck key. If the error still occurs-- 8. Replace the power supply. check over here If the error still occurs - 2.

Replace the control panel circuit board. 4 External electrical noise (AC line noise) can interfere with the (RPM) signal between the power supply and the control panel. I can't believe it, Thank you!!!” Amiee- Yesterday “I spent all day trying to sort this out then found your site. I too have error code 31 and need helpthanks Oct 09, 2014 Rating Error code 31 by: Sri How to resolve error code 31, pleaseee Aug 22, 2013 Rating error codes External electrical noise (AC line noise) can interfere with the (RPM) signal between the power supply and the control panel.

The beeper will turn off 4 seconds after the raw potentiometer data is within the 48 to 244 range. 6. Worked a treat!” Daren- 1 Month Ago “Thanks for sharing, I no longer have to put up with the dreaded Pacemaster Proselect Error Code 31 Treadmill” Eloy- 2 Months Ago “Will If the error occurs well into the program and does not occur each time the treadmill is used, skip to step 4. 1. Adding a picture is an excellent way to increase your credibility and keep your readers interested.

I have a Nordic track vr25 elite. Sign in Transcript Statistics 1,419 views 15 Like this video? user-manual-790... In the unlikely event that this does not correct the error - 3.

Time window will display raw potentiometer data; Incline window will display % elevation; Data window will display oFF. Also, check to see that the disc is not bent or wobbly and that it is not making contact with the optical sensor. 4.