Home > Pacemaster Pro > Pacemaster Treadmill Error Code

Pacemaster Treadmill Error Code


ELEVATION ERROR - (ELE Err) - Indicates the control panel has not sensed an elevation change that was requested. Do You Think This Treadmill is Worth Buying? Error Code 53 - Elevation Error 34 Second time out. PANEL 00 - 18 - (PAn EL 00 - 18) Indicates the keyboard membrane has a stuck key. http://sisei.net/pacemaster-pro/pacemaster-treadmill-error-code-31.html

Replace the power supply circuit board. Replace as needed. 3. Now it is ok. Currently, I'm looking at puchasing another Pacemaster.My only complaint are those meanless codes.

Pacemaster Pro Plus Treadmill Troubleshooting

The material appearing on LIVESTRONG.COM is for educational use only. Elevation Test Mode 1. Sign in 1 Loading... Then select it.

It's free, fun and easy to do. Pull up older posts almost all ... If the problem still occurs- 2. Pacemaster Pro Plus Parts In the unlikely event that this does not correct the error - 5.

Steps to follow to determine and correct the problem. 2. ………………………………………………………………………… BAD RELAY - (bAd rEL Ay) Indicates malfunction of the safety power relay on the power supply. 1. Remove the magnetic key. Replace the drive motor. Andrew Maxsimic 62,781 views 5:00 Treadmill Troubleshooting - Duration: 1:17.

I have a nordictrack ACT pro elliptical. Pacemaster Treadmill Error Code 24 Press and hold simultaneously Calories and Aerobic Points buttons (for the ProClub use the Level+ & Level- Buttons) until unit beeps. Replace the power supply. Err Code 31 - (Dead Sensor) Indicates that the control panel is not sensing movement of the drive motor.

Pacemaster Pro Plus 2 Error Code 31

Bypass the wire harness between the control panel circuit board and the power supply circuit board. http://www.justanswer.com/fitness-equipment/62dkp-i-m-getting-error-code-31-pacemaster-proselect.html WEIGHT ft. Pacemaster Pro Plus Treadmill Troubleshooting Turn off the power and reset ... Pacemaster Proselect Treadmill Manual Although the result will be an ELE Err code since the elevation motor is disconnected, the fuse should be inspected.

It is important that you follow the steps in the order that they are listed to properly determine and correct the problem. this content The speedometer isn't 10/2/2016 10/2/2016 J.T. Check to see if the error is concurrent with the operation of other electrical or electronic devices such as: air conditioners, garage door openers, refrigerators, freezers or home security devices. Sign in Share More Report Need to report the video? Pacemaster Pro Plus Treadmill Dead Sensor

Moreover, we do not select every advertiser or advertisement that appears on the web site-many of the advertisements are served by third party advertising companies. PDF Manual Treadmill.pdf. Replace the power supply. weblink It should not be used as a substitute for professional medical advice, diagnosis or treatment.

Replace if needed. 3. Pacemaster Pro Plus Treadmill Owners Manual Walk on the treadmill to test if the slippage is improved. Step 5 Unplug the treadmill and check that the drive motor connection and ceramic fuse are securely attached and do not show signs of wear if you receive error code 425.

Restart the treadmill, if the error still occurs - 2.

Treadmill remains on when Magnetic Key is Removed - This occurs when the reed switch (a component on the upper circuit board) fails. Replace the control panel circuit board. 4. Enter Your E-mail Address Enter Your First Name (optional) Then Don't worry — your e-mail address is totally secure. Pacemaster Pro Plus Rpm Sensor ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: Connection to failed.

In rare cases, the power supply or control panel may need to be replaced. 1. Treadmill Doctor 37,362 views 4:49 My Treadmill Has No Power - Duration: 3:00. My treadmill no longer asks me for my weight, and I'd like to reset it. check over here If the error is corrected, install the spare wire harness.

This indication will appear between five to eight seconds after the start button is pressed. 1. Re-insert the magnetic key and resume normal operation. Replace the control panel circuit board. Press and hold simultaneously the + and - buttons in the Time Window for 3 seconds then release.

NOTE: in this mode, there is nothing to prevent the jamming of the nut at either end. in. If this does not correct the problem- 1. Distance window will display Pr-L (production limited mode). 4.

Great! Only thing I ever had to replace on it Read More Mr.